You are here: Often referred to as a drum, rope drum, or warping drum. The capstan is primarily used for hauling rope. Similarly, chain compressor.

1. Windlass Boat Anchor Systems

Windlass Horizon 600. I'll go the manual route. I bought mine from boatbandit.com it was $720 exact replacement installed for the Horizon 600 windlass and came.

Located between the winch and bow roller. Secures chain and anchor and takes the load off the winch/windlass. Highly recommended for systems utilising all chain and for semi-automatic rope and chain systems. Release of the winch clutch mechanism allowing the anchor and rode (chain or rope and chain) to run out freely with no engagement of winch gearbox or motor.

Often referred to as chainwheel or wildcat. A special wheel with pockets, to accommodate a specified chain size, for hauling up the chain and anchor. With automatic rope/chain systems the gypsy is designed to haul both rope and chain. Often referred to as weighing or lifting. The operation of lifting the anchor and rode. Pertaining to the winch or windlass. Drive shaft, capstan and gypsy are positioned horizontally to the deck.

Often referred to as emergency crank system. A means of manually cranking the winch to haul in the rode and anchor should a failure occur in the motor, gearbox or power supply. Sometimes referred to as rated lift, stall load, or simply lift/pull. The maximum pull or lift load of the winch.

Windlass Boat Anchor Systems

The line that secures the boat to the anchor. This may consist of all chain, all rope, or a combination of rope and chain. Pertaining to the winch or windlass.

The drive shaft, capstan and gypsy are positioned vertically to the deck. A windlass driven by a hand or power-operated crank or gearbox.

Often implies to pull or lift a weight by using a winch. A machine for raising a weight by winding a rope and/or chain around a drum or chainwheel, driven by a crank, motor, etc. Often referred to as the normal working load or the typical lift of the winch. This is usually somewhere between 25% to 35% of the maximum pull or rated lift. This workload should approximately correspond to the total weight of the anchor and rode aboard the boat. Vertical vs Horizontal Winches Vertical systems have several advantages: They take up less space on deck and are easier to maintain.

They are less expensive than equivalent horizontal models. Chain alignment for smooth chain retrieval, while important, is not as critical as horizontal windlass alignment. With vertical systems more chain is in contact with the chainwheel thus avoiding the possibility of chain jump. Line-pull on the warping drum can be in any direction, as opposed to fore and aft only on horizontal models.

Horizontal models have the advantage of being better suited to applications where there is limited below deck space / accessibility, extreme deck thickness (over 200mm - 8'), or where two anchors must be handled from one winch. We are proud to serve you with any assistance via email or Toll free number at 1-877-406-4562 for USA or (858) 925-7705 for International Customers. Secure-Server that supports industry-standard SSL Encryption for your Safe Online transaction All personal information you submit is encrypted and 100% secure We offer online shipment tracking Recommended Site: Thank you for visiting Marinedeal for your and! Garmin Authorized Reseller Raymarine Authorized Reseller Simrad Authorized Reseller Lowrance Authorized Reseller Furuno Authorized Reseller Humminbird Authorized Reseller KVH Authorized Reseller JRC ACR Comnav Authorized Reseller Icom Intellian Lewmar Authorized Reseller Authorized Reseller Xantrex B&G Authorized Reseller Blue Sea System Seastar Teleflex Si-Tex Authorized Reseller Mastervolt ProMariner Newmar Jabsco Magnum Authorized Reseller Raritan.

With over 125 years of experience, Schoellhorn-Albrecht Machine Co., Inc. is one of the leading designers and manufacturers of marine deck equipment, dock equipment, and vessel access systems. In addition to a standard product line, we also specialize in designing and manufacturing castings, fabrications, and specialized machinery. Due to our custom design and manufacturing capabilities, our products serve a variety of industries, including: marine, railroad, refinery, and military. Products that we have designed and manufactured include: capstans, winches, mooring winches, anchor windlasses, tugger winches, anchors, deck fittings, bitts, chocks, cleats, mooring rings, hatches, kevels, roller chocks, roller fairleads, smit brackets, bollards, dock cleats, panama chocks, accommodation ladders, and gangways.

With the authority of the Directorate of Defense Trade Controls (DDTC), Schoellhorn-Albrecht Machine Co., Inc., is compliant to the Arms Export Control Act (AECA) and the International Traffic in Arms Regulations (ITAR). Please contact for more details. Marine capstans, ship capstans, pull-pak capstan, 'pull-pak' capstan, fmc capstans, pull pak, 'pull pak' 110A. Branford marsalis transcriptions.